首推-suncitygroup太阳集团_欢迎您

注意事项

锯片使用注意事项/Attention


●作业环境/Operating Conditions

●机械要安装保护罩,防止因锯片破损、碎片飞散等造成伤害。

●无关系者禁止靠近作业场所。

●作业场所应远离易燃、易爆品。

●Machine cover is essential to minimize the injuries by flying broken blades.

●Rrelevant people are allowed in the work shop.

●Flammables and explosives should be kept away from the work floor.


●服装、防护用具/Safety Measures

●作业者必须佩带保护眼镜,防止因锯片破损、碎片飞散等造成伤害。

●作业都必须注意领带及袖口,不能戴手套,长发要置于工作帽

内,防止被卷入机器,发生危险。

●Wear glasses when working, to prevent from injuries by broken blades.

●Watch out for your ties and sleeves. Long hair should be kept inside the cap, and no gloves are allowed during operation.


●使用前的准备/Before Use

●确保机器状态良好,主轴无变形、无振动、轴径公差为h7。

●检查锯片有无欠损、脱落、异常磨耗以及本体的弯曲、扭曲、破裂等异常现象,以防锯片破损、飞散造成的伤害。

●确认所选锯片是否适合被切削材料,防止锯片的异常磨耗、脱落、切割不良、过热等异常状况发生。如选择错误,可能造成锯片破损、碎片飞散,发生意外事故。

●Ensure the machines are in good condition with no deformation and no spindle vibration, the spindle's running tolerance can be h7.

●Make sure the blades are not excessively worn-out, blade body has no defomation or breaks leat injuries occur.

●Make sure appropriate sawblades are used.


●安装/Installation

●保证锯片回转方向与机器主轴回转方向一致,如果方向相反,会造成刀片脱东、碎片飞散,发生意外事故。

●选择内径与锯片内径一致、外径为锯片外径1/3略大(多片锯宜采用锯片外径1/2)的法兰盘,确认其无异常磨虚耗、弯曲变形、表面洁净无异物附着。

●保证锯片内径与机器轴径之间无过大间隙,安装好法兰盘,拧紧螺母。

●作业前,确认锯片前方无人。然后空转,检查机器有无振动、锯片有无横向及径向摆动等异常现象。

●锯片的再加工(内经修正、定位孔加工等)必须由厂方进行。如果加工不良,会影响产品使用效果,并且可能发生危险。

●安装时,一般锯片高出板材5- 6锯齿为宜。

●Ensure the sawblade turns in the same direction as the spindle does.If not, accidents are likely to occur.

●Choose the flange whose inner diameter is the same as that of the sawblade but the outer diameter is a lttilel larger than 1/3(for multi-rip sawblade is 1/2)of the sawblade. Ensure the flange is clean, not over worn, bent and distorted shape.

●Check the tolerance between the sawblade and the spindle. Install the flange and festen and fasten the screw.

●Be sure no people stand in front of the machine when starting the machine. Do not feed, just to check whether there is any vibration, radial or axial run out.

●Sawblade reprocessing such as bore trimming or reboring,should be finished by the factory. Poor reprocessing would lead to poor quality and may cause injuries.

●While installation, the sawblade should be 5-6 teeth higher than the board surface.


●使用中/In Use

●使用时,被切削材料需要固定,以免造成异常切入,从而导致锯片破损、碎片飞散,发生意外事故。

●使用时,发现声音和振动异常、切割面粗糙、弯曲时,必须终止作业,及时检查,排除故障。如继续使用,会造成锯片破损、碎片飞散,发生意外事故。

●In operation wood materials should be properly fixed, if not, abnormal cutting may occur.

●The operation must be stopped rightly once unusual noise and vibration occurs, if not, rough surface and tip-breaking may occur.


●使用后/After Use

●当锯片不再锋利、切断面粗糙时,必须及时进行再研磨。否则,会影响使用效果,并可能造成锯片报废,发生意外事故。

●再研磨必须又可信赖的专门厂家进行,不能改变原角度。

●Sawblades should be resharpened because dull sawblades may affect cutting effect and lead to

accidents.

●Resharpening should be made by professional factories, not changing the orginal angle degrees.